Solar
Solar Panels
Solar Charge Controllers
Mounting
Solar Accessories
Solar Kits
Batteries
Batteries
Battery Management
Battery Boxes
Battery Kits
Chargers
Mains Chargers
DC-DC Chargers
Alternators & Regulators
Charger Kits
Inverters
Inverters
Inverter Kits
Electrical
Circuit Protection
Connectors, Busbars & Terminals
Switch Panels & Accessories
240V Equipment
EV Chargers
Cables
Cables
Pre-made Leads
Cable Management
Converters
DC-DC Converters
Transformers
Monitoring
Monitoring
Monitoring Kits
Kits
Pre-Wired Boards
4x4/Canopy Power Systems
Solar Kits
Inverter Kits
Charger Kits
Battery Kits
Monitoring Kits
By Application
Caravan, Camper & RV
Camping & Portable
Marine/ Boat
4x4/4WD & Off-Road
Off-Grid Homes & Sheds
Golf Carts
Portable 12V Car Chargers
Portable 24V Bus/Truck Chargers
By Brand
Pre-Wired Boards
4x4/Canopy Power Systems
Solar Kits
Inverter Kits
Charger Kits
Battery Kits
Monitoring Kits
Battery Charger Mounts & Cases
Wall mounts, rubber bumpers and carry cases sized to fit Victron IP65 battery chargers.
Mounting and Protection for Victron IP65 Battery Chargers
A battery charger that is fixed in place or properly protected is easier to use and easier to look after. This range of Victron wall mounts, rubber bumpers and carry cases is designed for Victron IP65 battery chargers. You can permanently install a wall mounted battery charger in a caravan, workshop or boat, or protect a portable unit you move between vehicles and sites.
Each accessory is sized for a specific group of IP65 charger models. Match the accessory to your charger's voltage and current rating (for example, 12/15 means 12 V at 15 A) before ordering.
Choosing the Right Accessory
The best option depends on how you use your charger:
- Victron Wall Mount: For a fixed, mounted battery charger installation. It holds the charger securely on a wall or bulkhead so the unit stays off the floor and away from foot traffic.
- Victron Rubber Bumper: Adds a protective rubber surround to the charger housing. It helps protect against knocks and scuffs when the charger is used on benches, in tool bays or around the workshop.
- Victron Carry Case: Keeps the charger and its leads together for transport and storage. It suits shoppers who carry a charger in the 4WD, boat or work vehicle.
If you are still choosing a charger, our Victron mains chargers comparison sets out the differences between models. That makes it easier to pick both the charger and the matching mount or case.
Compatibility Notes
Fitment is model-specific, so check your charger's rating label against the sizes below:
- Smaller IP65 chargers (12/10, 12/15, 24/8): Choose the Victron Wall Mount or Victron Rubber Bumper sized for these models. The matching Victron Carry Case suits IP65 chargers up to 12/15 and 24/8.
- Larger IP65 chargers (12/25, 24/13): Choose the Wall Mount, Rubber Bumper and Carry Case versions sized for these models.
When wall mounting, choose a dry, ventilated location with clearance around the charger for airflow. Keep the DC leads short enough to reach the battery without strain. To finish the installation, browse our battery charger cables and connectors. You can also return to the full range of battery charger accessories.
Protect and Organise Your Charger
A Victron accessory sized to your charger keeps it secure, protected and ready to use, whether it is fixed in a caravan or workshop or carried between jobs. Confirm your IP65 charger model, then select the matching wall mount, bumper or carry case to complete your charging setup.